Burning bar Thermal lance. Home / Products / Thermal lance / When the steel becomes cherry red a high pressure jet of Sure Cut Rods and Underwater Cutting Rods. 106 Burning Bars are available in Pipe and Tube sizes from .540 O.D. up to 1.05 O.D. The smaller Sure Cut Rods are available in Tube sizes of 1/4 and 3/8 O.D
Jul 28, 2015 · Burning Lance And Thermal Lance Pipe - Anaya Steel We are the pioneers in manufacturing of Calorized refractory-coated lancing pipes universally. Our pipes are mostly used in Steel Melting Shops, Blast Furnaces area in different applications like CDI/ PCI, blowing of oxygen gas, Carbon, Argon etc , degassing of VOD unit, slag cutting into the Calorized Lance And Thermal Lance Pipe - AnayasteelJun 21, 2015 · Calorized refractory coated lance pipe and High Quality Burning Lance Pipe is a very important tool for oxygen steel making as in this process of steel manufacturing by open hearth or electric furnace, the consumption rate of lance pipes for oxygen injection sows rather high ratio owing to high temperature and severe oxidation.
In the process of steel manufacturing by open hearth or electric furnace, the consumption rate of lance pipes for oxygen injection slows rather high ratio owing to high temperature severe oxidation. In general, steel pipes are used as lance pipes for oxygen injection. DIY Thermic Lance Kit - Cut Steel With Burning Iron :4
The addition of power steel rods in packed form to a lance pipe, provides a greater ratio of iron to oxygen, thus providing sufficient heat to melt ferrous and non-ferrous materials. The lance is ignited by applying heat to the lance end with an oxygen-acetylene equipment. OXYLANCE BURNING BARS AND ACCESSORIESThe Oxylance Burning Bar is a 10' 6" consumable thermal pipe designed to economically cut, sever or burn holes through all types of ferrous and non-ferrous metals and materials more efficiently and cleaner than any conventional bar on the market today.
- Principles of OperationConcreteSteelSpecification-Oxygen LancingSafetySummaryAn oxyfuel gas torch is used to bring the cutting end of the lance to white heat, and then the oxygen valve is slowly opened to start O2 flow, and initiate the burning operation of the packed lance. The higher the oxygen pressure the higher the burning intensity. The oxygen valve is opened further, and shall be fully open in about 1 to 2 cm cutting depth. A close oxygen flow control will help reduce heavy sparking at start of cut. The deeper the cut the more sparks are eliminated. A baffle plate shall be used in all applicationLance a Job - Lancing Equipment, Oxygen Lancing Set3/8" Wire Packed Thermal Lance:16mm outside diameter lance used to cut concrete, brass, copper, aluminium, cast iron and steel:098-726:3/8" Open Thermal Lance:16mm outside diameter open lance used in foundries and steel plants to open furnace tap holes:098-725 (Other lance sizes available)
Steel Mill ProductsSteel Mill Products Oxygen Lance Pipe. Home / Steel Mill Products / Calorized Oxygen Lance Pipe. Burning Bars. Cutting of large scrap pieces, skulls, titanium, carbon steel, metal spills, sprues, refractories and concrete. Holders. Standard, shielded, anti slag return device, quick release.
A Thermal Lance, thermic lance, oxygen lance, or burning bar is a tool that heats and melts steel in the presence of pressurized oxygen to create the very high temperatures (3600)required for cutting. Sturdy, Stainless lance pipe for Industry Uses - With seamless welding quality, these lance pipe are annealed with nitrogen protection and are polished with utter professionalism. These products are made of robust materials such as carbon steel, stainless steel, galvanized surface-treated iron and many more to offer consistent service for a long time.
Steel pipe 1 O2+powder circuit slag Steel rods Steel pipe 2 Fig. 4. Lance types for thermal cutting with internal O 2 circuit In order to increase lance cutting speed along with internal carbon steel rods one or two aluminum, copper, titanium rods are inserted as well (Figure 5). Fig. 5. Lance for thermal cutting with steel and Cu rods Thermal Lance Manufacturer,Thermal Lance Supplier,ExporterThermallance also named thermic lance, oxygen lance, cutting lance or burning bar,etc. It creates a high temperature at least 3600 when burned along with oxygen. The far end of the tube is pre-heated and lit by an oxyacetylene torch.
Thermal Lance. A Thermal Lance, thermic lance, oxygen lance, or burning bar is a tool that heats and melts steel in the presence of pressurized oxygen to create the very high temperatures (3600°C) required for cutting. It consists of a long steel tube packed with alloy steel rods, sometimes mixed with aluminium rods to increase the heat output. Thermal lance - GD AparatosBurning Bar. A Burning bar is a lance for cutting that uses only oxygen. It is able to cut any type of material:metallic (steel, stainless steel, high nickel alloys, copper and bronze alloys, aluminum, manganese and shielding steels and any type of alloy) or non-metallic ones (ceramic, concrete, refractory bricks etc.); in short, this thermal lance can cut or pierce any known material.
BURNING LANCE is the product developed, for the purpose increasing the heat quantity g US $8.00 / KG Min. Order 1,000.00 KG Kandi Engineering Pvt. Ltd. What is a Thermic Lance?A Thermic Lance is a steel pipe packed with mixed metal wires. Pure oxygen gas is passed through the pipe from an oxygen cylinder and regulator. The end of the pipe is lit with a high temperature source, e.g. an oxy-acetylene torch. The iron in the steel burns in the oxygen coming down the pipe to produce enormous heat and a liquid slag of iron
Thermic lance/burning lance pipe/thermal seamless steel pipe. $750.00 - $950.00 / Metric Ton. 10 Metric Tons (Min. Order) ISO Certificatited seamless steel pipe Cheap Prices dubai pipe scrap. $10.00 - $50.00 / Metric Ton.Thermal cutting lance Products for Sale - Metal and SteelThermal lance also named thermic lance, oxygen lance, cutting lance or burning bar, etc. It creates a high temperature at least 3600 when burned along with oxygen. The far end of the tube is pre-heated and lit by an oxyacetylene torch. An intense stream of burning steel is produced at the workpiece end and can be used to cut rapidly through thick materials including steel and concrete.